Information Sharing Among Disaster Responders - An Interactive Spreadsheet-Based Collaboration Approach

Recent natural disasters have led crisis management organizations to revise their protocols so as to rely on the contribution of a wider range of actors, including simple citizens as well as expert operators, to support decision making activities. Reliable and timely information sharing among members of distributed teams of disaster responders has become paramount for the success of the overall crisis management process. In this paper we propose a crisis management system based on spreadsheet-mediated collaboration among on-site responders and decision makers. To share data a common spreadsheet artifact has been developed by using a participatory design approach which is accessed through mobile user interfaces. The evaluation results showed that the use of the spreadsheet artifact has resulted in more effective decision making relating to set of earthquake management scenarios in high-risk areas located in Italy.     

Solar barometric distillation for seawater desalting part I: Basic layout and operational/technical features

The report presents an innovative solar barometric distillation technology for seawater desalting (SW-SBD) which has several attractive features such as: (1) efficient vacuum solar collectors of simple construction; (2) a barometric layout for quasi-steady operation at subatmospheric pressure; (3) a demister system of simple mechanical construction; and (4) an electronic control system regulating plant productivity parameters on available solar radiation flux. The proposed seawater desalting technology consists of single-effect distillation with water vapor produced and heated at subatmospheric pressure in a solar collector loop; the basic layout, operational features, and energy efficiency are presented and analysed in detail. Subsequent reports will provide technico-economical data from prototype desalting plants in view of industrial implementation. A promising specific electric energy consumption,∼2 kWm³ offresh water produced, was found by estimating pumping power requirements of major SW-SBD plant pumps. A sizable reduction in produced water cost with respect to an existing solar seawater desalting plant in Abu Dhabi is expected on the basis of a preliminary economic evaluation for a ∼100 m³/d plant prototype.     

Electrochemical anticorrosion performance evaluation of Al2O3 coatings deposited by MOCVD on an industrial brass substrate

Alumina (Al₂O₃) coatings of different thickness were deposited on OT59 brass substrate (BS) using the metal organic chemical vapour deposition (MOCVD) technique to evaluate the corrosion performance by EIS measurements. The used precursor was dimethyl-aluminium-isopropoxide. Electrochemical characterizations of the deposited films were performed in a standard very aggressive acidic solution (aerated 1N H₂SO₄ at 25 °C up to 168 h of immersion time) by means of direct current method (Tafel curves) and electrochemical impedance spectroscopy (EIS). The Rutherford backscattering spectroscopy (RBS) indicated that the films are very pure with the correct Al₂O₃ stoichiometry, while the IR absorption spectra showed that the films did not contain any OH groups. The surface film morphology was investigated by atomic force microscopy (AFM) and displayed a globular texture. The films were very smooth, with a maximum root mean square roughness, for example, of 14 nm for a 0.96 μm thick coating. The EIS data confirmed, as expected, that a 2.40 μm Al₂O₃ layer ensures the best corrosion protection after 168 h of immersion in the very acidic environment used.     

Fluoroelastomers-dependence of relaxation phenomena on composition

The dynamic-mechanical properties of some fluoroelastomers were determined as a function of composition at low frequency (≈ 1 Hz), by means of a free oscillation torsion pendulum, between −180°C and the softening point. Vinylidenefluoride (VDF)-hexafluoropropene (HFP) copolymers of molar composition 0–39% HFP and terpolymers of VDF and HFP with up to 30mol% tetrafluoroethylene (TFE) and a constant VDF to HFP molar ratio of 3.4 were considered. Two relaxation processes typical of the amorphous phase were found. The first, located at about −87°C, is related to local motions and the transition temperature was found to be independent of composition for copolymers, while it depends on TFE molar content for terpolymers. The second is related to the glass transition and the transition temperature depends on the composition. However, for semicrystalline copolymers the double glass transition phenomenon was observed. When crystallinity goes to zero at about 20 mol% HFP, only one transition is observed. It was also found that ordered structures can take place for terpolymers when TFE molar concentration exceeds 20%. The crystal disorder transition of pure PVDF (75°C) is observed also for low HFP concentrations but the transition temperature is strongly reduced. Analogies between the VDF-HFP and E-P systems are also discussed.     

Straightforward modeling of dynamic I–V characteristics for microwave FETs

This work presents a straightforward approach aimed at modeling the dynamic I–V characteristics of microwave active solid‐state devices. The drain‐source current generator represents the most significant source of nonlinearity in a transistor and, therefore, its correct modeling is fundamental to predict accurately the current and voltage waveforms under large‐signal operation. The proposed approach relies on using a small set of low‐frequency time‐domain waveform measurements combined with numerical optimization‐based estimation of the nonlinear model parameters. The procedure is applied to a gallium nitride HEMT and silicon FinFET. The effectiveness of the modeling procedure in terms of prediction accuracy and generalization capability is demonstrated by validation of the extracted models under operating conditions different than the ones used for the parameters estimation. Good agreement between measurements and model simulations is achieved for both technologies and in both low‐ and high‐frequency range. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:109–116, 2014.     

Reactive Compatibilizer Precursors for LDPE/PA6 Blends, 4

Summary: The effectiveness of some thermoplastic elastomers grafted with maleic anhydride (MA) or with glycidyl methacrylate (GMA) as compatibilizer precursors (CPs) for blends of low density polyethylene (LDPE) with polyamide‐6 (PA) has been studied. The CPs were produced by grafting different amounts of MA or GMA onto a styrene‐block‐(ethylene‐co‐1‐butene)‐block‐styrene copolymer (SEBS) (KRATON G 1652), either in the melt or in solution. A commercially available SEBS‐g‐MA copolymer with 1.7 wt.‐% MA (KRATON FG 1901X) was also used. The effect of the MA concentration and of other characteristics of the SEBS‐g‐MA CPs was also studied. The specific interactions between the CPs and the blends components were investigated through characterizations of the binary LDPE/CP and PA/CP blends, in the whole composition range. It was demonstrated that the SEBS‐g‐GMA copolymers display poor compatibilizing effectiveness due to cross‐linking resulting from reactions of the epoxy rings of these CPs with both the amine and the carboxyl end groups of PA. On the contrary, the compatibilizing efficiency of the MA‐grafted elastomers, as revealed by the thermal properties and the morphology of the compatibilized blends, was shown to be excellent. The results of this study confirm that the anhydride functional groups possess considerably higher efficiency, for the reactive compatibilization of LDPE/PA blends, than those of the ethylene‐acrylic acid and ethylene‐glycidyl methacrylate copolymers investigated in previous works.

SEM micrograph of the 75/25 LD08/PA blend (with 2 phr SEBSMA1).     

Heat Induced Structure Modifications in Polymer‐Layered Silicate Nanocomposites

Summary: The success of the use of layered silicates in polymer nanocomposites, to improve physical and chemical properties is strictly related to a deeper knowledge of the mechanistic aspects on which the final features are grounded. This work shows the temperature induced structural rearrangements of nanocomposites based on poly[ethylene‐co‐(vinyl acetate)] (EVA) intercalated‐organomodified clay (at 3–30 wt.‐% silicate addition) which occur in the range between 75 and 350 °C. In situ high temperature X‐ray diffraction (HT‐XRD) studies have been performed under both nitrogen and air to monitor the modifications of the nanocomposite structure at increasing temperatures under inert/oxidative atmosphere. Heating between 75 and 225 °C, under nitrogen or air, causes the layered silicate to migrate towards the nanocomposite surface and to increase its interlayer distance. The degradation of both the clay organomodifier and the VA units of the EVA polymer seems to play a key role in driving the evolution of the silicate phase in the low temperature range. The structural modifications of the nanocomposites in the high temperature range (250–350 °C), depended on the atmosphere, either inert or oxidizing, in which the samples were heated. Heating under nitrogen led to deintercalation and thus a decrease of the silicate interlayer space, whereas exfoliation was the main process under air leading to an increase of the silicate interlayer space.

Heat induced structural modification of EVA‐clay nanocomposite under nitrogen and air.     

A flexible FPGA implementation for illuminance–reflectance video enhancement

Digital cameras, new generation phones, commercial TV sets and, in general, all modern devices for image acquisition and visualization can benefit from algorithms for image enhancement suitable to work in real time and preferably with limited power consumption. Among the various methods described in the scientific literature, Retinex-based approaches are able to provide very good performances, but unfortunately they typically require a high computational effort. In this article, we propose a flexible and effective architecture for the real-time enhancement of video frames, suitable to be implemented in a single FPGA device. The video enhancement algorithm is based on a modified version of the Retinex approach. This method, developed to control the dynamic range of poorly illuminated images while preserving the visual details, has been improved by the adoption of a new model to perform illuminance estimation. The video enhancement parameters are controlled in real time through an embedded microprocessor which makes the system able to modify its behavior according to the characteristics of the input images, and using information about the surrounding light conditions.